Partition Water tank



Partition water tank
If tanks for two different uses are needed in a confined area or boiler room,
a 20 ton partition type tank can be installed to use half for drinking water,
and half for service water. If separate tanks are installed, however, you have to installed...
two tanks with a maximum of 8 tons, because you need to have 1 meter distance
between tanks for maintenance and operating space

Feature
Utilizing Maximum Capacity
It is recommended to eliminate unusable space and utilize the
maximum space by the installing a partition tank

Various uses
If partition type tanks are installed, one section can be used for drinking
water and the other section for service water(fire fighting)

Easy maintenance
It is convenient for maintenance because tanks can be installed as one unit.

Cost Effectiveness
The cost and installation of 1 partition tank is more economic than 2 separate tanks

DAEJOO ENG. CO.,LTD
Website : www.daejoosmc.com
E-mail : biotank420@gmail.com
Sky Seo's Mobile / Whatsapp : +82-10-2758-7147
GM's Mobile / Whatsapp : +82-10-7741-8555

Comments

Post a Comment

Popular posts from this blog

Check steel skid base

Image
Check steel skid base Basic structure of steel footing is the cross-hatched type. A) Standard of Steel Skid Per Height B) Assembling for Steel Skid 1) All bolts/nuts for connecting steel skid shall be M14 X 40 ℓ. 2) Joint Angle( or Channel) at intervals of 1M using base frame 3) Put Angle(or Channel) on base PAD and joint using ㄱtype Bracket (7575Z) DAEJOO ENG. CO.,LTD ​ Sky Seo (Managing Director) Website : www.daejoosmc.com Blog1 :  grp-water-tank.blogspot.com Blog2 :  blog.naver.com/biotank420 E-mail : biotank420@gmail.com Managing Director's Mobile / Whatsapp : +82-10-2758-7147 General Manager's Mobile / Whatsapp : +82-10-7741-8555
Read more

Water tank view and Parts name

Image
Water tank view and Parts name Panel Name 1. Side panel(1m x 2m) 2. Side panel(1m x 1m) 3. Manhole(Φ750) 4. Roof panel 5. Flange panel 6. Bottom panel 7. Drainage panel 8. Partition panel Parts Name a. Concrete Foundation b. Steel skid c. Drainage d. Outlet e. Corner flame f. Over flow g. Air vantilator h. External ladder i. Internal ladder j. Inlet k. Reinforcing angle l. Outer bracket m. Plate bar n. Inner Backet o. Tie rods DAEJOO ENG. CO.,LTD ​ Sky Seo (Managing Director) Website : www.daejoosmc.com Blog1 :  grp-water-tank.blogspot.com Blog2 :  blog.naver.com/biotank420 E-mail : biotank420@gmail.com Managing Director's Mobile / Whatsapp : +82-10-2758-7147 General Manager's Mobile / Whatsapp : +82-10-7741-8555
Read more

Installation of Internal Ladder

Image
Installation of Internal Ladder. Install the internal ladder and poles from the tank interior, after the connection of the roof panel block to side panel blocks. It is advisable to carry the internal ladder and poles into the tank before connecting the roof panel to the side panel block. Material is GRP DAEJOO ENG. CO.,LTD ​ Sky Seo (Managing Director) Website : www.daejoosmc.com Blog1 :  grp-water-tank.blogspot.com Blog2 :  blog.naver.com/biotank420 E-mail : biotank420@gmail.com Managing Director's Mobile / Whatsapp : +82-10-2758-7147 General Manager's Mobile / Whatsapp : +82-10-7741-8555
Read more